Quick answer

Going from 60 to 144 to 240 Hz shortens each refresh from 16.7 ms to 6.9 ms to 4.2 ms. RTINGS says a higher refresh rate gives smoother motion, and by Blur Busters’ rule for sample-and-hold screens eye-tracking blur falls with the frame time. Both depend on your game’s frame rate rising with it and on your cable, port and Windows setting running the panel at its rated mode.

Contents

Provenance

  • Nov 18, 2026Published

Refresh rate is one of the few monitor specs you can reason about with a calculator, so I’ll start there. Everything after the table about blur, perception and aiming belongs to a named source; I haven’t measured motion clarity, input lag or frame rates for this page. My own screen is the AORUS FO48U, a 48-inch-class 4K OLED that tops out at 120 Hz, and it’s the only monitor connected to my bench PC, so I have no 144 Hz or 240 Hz panel to set beside it.

The arithmetic

Time per refresh is 1000 divided by the refresh rate. To put a new frame on every refresh, the game has to deliver as many frames per second as the panel has hertz. This table is arithmetic, not a measurement; RTINGS prints the same time-between-frames figures in its refresh-rate test article.

Refresh rateTime per refresh (1000 ÷ Hz)Frame rate needed for a new frame every refresh
60 Hz16.67 ms60 fps
120 Hz8.33 ms120 fps
144 Hz6.94 ms144 fps
165 Hz6.06 ms165 fps
240 Hz4.17 ms240 fps

There are two ways to read it. In absolute time, 60 to 144 Hz takes 9.72 ms off every refresh and 144 to 240 Hz takes 2.78 ms. As a ratio, 60 to 144 Hz is a 2.4x step, 144 to 240 Hz is 1.67x, and 60 to 240 Hz is 4x. Blur Busters argues the ratio is what your eyes respond to, which comes up again below.

What Hz means on a monitor

Microsoft’s refresh-rate page defines the refresh rate as the number of times per second the image on the screen refreshes, so a 60 Hz display updates the screen 60 times a second. RTINGS adds the direction: each refresh redraws the screen from top to bottom. AMD’s display article describes it as how many times the screen is redrawn per second and sends you to your display’s manual for the rates your model supports.

Refresh rate is not frame rate

Hz belongs to the monitor. Frame rate, in fps, is how many frames per second the PC or console sends, per RTINGS, which says you ideally want the two to match and that a mismatch can show up as stutter or screen tearing. Variable refresh rate is the feature that makes the monitor follow the frame rate instead; RTINGS describes it as syncing the monitor’s refresh rate to the source’s frame rate to reduce tearing when your frame rate drops. Which switches to set is on my variable refresh rate and V-Sync pages, and the screen tearing guide walks the whole chain, so I won’t repeat it here.

Refresh rate is not response time

RTINGS’ response-time article defines response time as how long a pixel takes to change from one colour to another, and says a slow one leads to smearing, blur or inverse ghosting. Blur Busters’ GtG versus MPRT FAQ splits the idea in two. GtG (grey-to-grey) is how long a pixel takes to change between two colours. MPRT (moving picture response time) is how long it stays continuously visible, and MPRT is limited by the refresh cycle and the frame time. The same FAQ says most 60 Hz displays, OLEDs included, have an MPRT of at least 1/60 s, 16.7 ms, however fast their pixels change, which is why near-instant pixels alone don’t remove motion blur.

The two specs work together. In its refresh-rate article, RTINGS shows two 180 Hz monitors whose total response times it measured at 6.8 ms and 14.7 ms, and says motion looks worse on the slower one at the same refresh rate. The 1 ms GtG on a spec sheet, like the figure Gigabyte lists for my FO48U, is the first kind of number, not the second.

Why a higher refresh rate can mean less motion blur

Blur Busters’ page on OLED motion blur explains sample-and-hold: the screen shows each frame unchanged until the next refresh, and it counts most LCDs and OLEDs as sample-and-hold displays. Your eyes keep moving while you track something, so they sit in a different place at the end of a refresh than at the start, and the held frame smears across your retina.

Blur Busters Law, a 2017 feature by Mark Rejhon updated in December 2020, turns that into a rule: 1 ms of persistence gives 1 pixel of motion blur for every 1,000 pixels per second of motion, and on a sample-and-hold screen persistence can’t be shorter than one frame. Its own worked numbers, at 1,000 pixels per second, are 16.7 pixels of blur at 60 fps, 8.3 at 120 fps and 4.1 at 240 fps (the page truncates; 1000 ÷ 240 is 4.17). The same rule gives 6.9 pixels at 144 fps; that one is my arithmetic. With the frame rate matching the refresh rate, persistence as a share of 60 Hz is 41.7 percent at 144 Hz and 25 percent at 240 Hz, and 240 Hz is 60 percent of 144 Hz (more arithmetic).

Three conditions sit under those numbers, all from Blur Busters:

  • They assume instant pixel response. The Law page says real panels with slower GtG land above that floor. Rejhon’s December 2024 article puts the difference between 60 and 120 Hz at a full 2x on a fast OLED, about 1.5x on a desktop gaming LCD and as little as about 1.1x on a laptop LCD without overdrive.
  • The frame rate sets the blur, not the refresh rate on its own. The 2024 article puts display motion blur on a sample-and-hold screen equal to the frame time, assuming zero GtG. The GtG FAQ adds that the motion blur of 60 fps can look identical on a 60, 120 or 240 Hz display, so a 240 Hz monitor showing a 60 fps game still holds each frame for 16.7 ms (1000 ÷ 60).
  • At low frame rates the blur becomes stutter. The Law page says the same rule then describes how far the image jumps rather than how far it smears.

Strobing and black frame insertion are the other route to shorter persistence. They’re on my motion blur page, along with the in-game blur setting.

Refresh rate also puts a floor under input lag. RTINGS lists the minimum input lag each rate allows, measured at the centre of the screen: 8.33 ms at 60 Hz, 3.47 ms at 144 Hz and 2.09 ms at 240 Hz. It says a higher refresh rate makes lower input lag possible but doesn’t guarantee it.

Will I notice?

I can’t answer that for you, and the sources I trust don’t agree on how much it matters.

  • Blur Busters says bigger jumps are easier to see. Rejhon’s December 19, 2024 article argues that visibility follows the ratio between two rates, like a camera shutter at 1/120 s against 1/480 s, and calls comparisons of small steps such as 144 to 165 Hz useless. Its argument is built around a fast OLED with near-zero GtG and frame rate equal to refresh rate, and it is Blur Busters’ own claim, not an independent test. The article says Blur Busters has completed an internal blind study, not yet published, showing 120 versus 480 Hz is more visible than 60 versus 120 Hz, and that it is looking for partners to fund a public one. By that reasoning, 60 to 144 Hz (2.4x) is a bigger step than 144 to 240 Hz (1.67x).
  • NVIDIA’s researchers found latency mattered more than refresh rate for aiming. In a November 2019 SIGGRAPH Asia technical brief, Josef Spjut and seven co-authors separated the two by adding latency at high refresh rates. Eight skilled esports players did first-person targeting tasks. Lower latency clearly cut task completion time, while refresh rate had relatively minor effects once the latency reduction that comes with high refresh rates was taken out, with a small, marginally significant effect from refresh rate alone in some tracking tasks.
  • RTINGS calls refresh rate one factor among several. It says a higher refresh rate gives smoother motion but isn’t the end-all of motion handling, and names response time as one of the other factors.
  • Microsoft lists the benefits as less motion blur and tearing, lower input lag and more fluid scrolling and pen input. That’s a vendor’s summary on a support page, not a test.

My own data point is one person’s impression, not a measurement: in my FO48U review I wrote that I came from a 60 Hz monitor and that 120 Hz on an OLED still feels incredibly smooth to me.

What has to keep up with the refresh rate

This part I can help with, because the sources above all assume three other things keep up with the refresh rate.

  1. The frame rate. By the persistence rule above, a 144 Hz or 240 Hz panel needs the game near 144 or 240 fps to show its full benefit, and RTINGS says your computer has to support high frame rates to reach a monitor’s maximum. My FPS calculator returns measured averages and 1% lows for exact tested combinations of CPU, GPU, game, resolution and preset, and returns no number for a combination nobody tested. The GPU hierarchy ranks 43 cards at 1080p, 1440p and 4K and lets you set your own card as 100 percent. Blur Busters’ 2024 article names frame generation as one way to the frame rates very high refresh rates need and treats it as a trade-off; frame generation explained covers what it costs. If latency is what you’re after, NVIDIA Reflex is the next page to read.
  2. The cable and the ports. RTINGS says the HDMI or DisplayPort inputs on both the monitor and the source need the bandwidth for the full refresh rate at native resolution. Its example is the AOC Q27G3XMN, a 1440p monitor rated for 180 Hz that reaches only 144 Hz over HDMI because of bandwidth. My DisplayPort and HDMI bandwidth calculator checks a resolution, refresh rate and colour depth against HDMI 2.0 and 2.1 and DisplayPort 1.4 and 2.1, with and without DSC. Its own worked example puts 1440p at 240 Hz in 8-bit colour at 24.6 Gbps uncompressed under VESA’s CVT-RB v2 timing: inside DisplayPort 1.4, outside HDMI 2.0. For 4K at 240 Hz, the 4K 240 Hz page has the full link table.
  3. The setting. Windows, the graphics driver and the monitor each have to be on the rate you paid for. That’s the next section.

How to check and change your refresh rate

Windows 11

These are Microsoft’s steps, from its support page as I read it today:

  1. Open Start > Settings > System > Display > Advanced display.
  2. The Display information panel shows the current resolution and refresh rate for the selected display, and whether the display supports variable refresh rate. That’s the check.
  3. To change it, pick a rate next to Choose a refresh rate. Microsoft says the list depends on what your display supports.

Microsoft adds one warning worth reading twice: rates marked with an asterisk (*) don’t support your current resolution, and choosing one changes the resolution to reach that rate. The same page covers Dynamic refresh rate, a separate Windows 11 feature that Microsoft says can limit the maximum refresh rate of games not designed for VRR; the variable refresh rate page has the detail. I didn’t open the Settings app for this page, so those are Microsoft’s labels, not my screenshots.

NVIDIA app

NVIDIA’s August 6, 2024 app beta announcement added a Displays section to the app’s System tab, with resolution, refresh rate and orientation controls for connected monitors and TVs. Its May 26, 2026 driver post retires the classic NVIDIA Control Panel for Game Ready and Studio drivers and says display options now live in the System tab. On my bench, the English string file installed with NVIDIA app 11.0.9.585 names that page Displays, with fields called Resolution and Refresh Rate. I didn’t open the app, so I’m not describing where each control sits on screen.

If the classic Control Panel is still on your PC, NVIDIA’s help page gives the old route: under Display, open Change resolution, select the display if you have more than one, and pick from the Refresh rate list. The same page notes that on a VRR-capable display with VRR enabled, the refresh rate is set to the highest rate automatically.

AMD Software: Adrenalin Edition

AMD’s display article (DH3-005, last updated November 8, 2024) gives no AMD Software path for the refresh rate. It sends you to Microsoft’s article to change it and to your display’s manual for the supported rates, so on a Radeon PC the Windows steps above are AMD’s own answer. There’s no Radeon card on my bench, so that’s AMD’s documentation, not my screen.

The monitor’s own menu

RTINGS says to set the refresh rate in the monitor’s on-screen menu as well, and to use its overclock or dual-mode setting if it has one and you want the top rate. BenQ’s troubleshooting article starts in the same place. On my FO48U, the Gaming menu reads Refresh Rate 120Hz in the OSD screenshots in my review.

What my bench reports

I ran read-only queries on the bench machine on November 17, 2026 (Windows 11 build 26200.9974, GeForce driver 621.24, RTX 5080 into the FO48U). Windows’ QueryDisplayConfig API, whose path target info carries the refresh rate as a numerator and denominator, returned 119999/1000 at 3840 x 2160: 119.999 Hz. The WMI Win32_VideoController class, whose CurrentRefreshRate field Microsoft documents as a whole-number value in hertz, returned 119. That’s the same mode read two ways, minutes apart. If a tool shows you 119 Hz on a 120 Hz monitor, read the exact rate before you assume something is wrong.

Stuck at 60 Hz: the documented causes

Work down this list in order. The first three cost nothing and change nothing on the hardware side.

  1. Windows is still set to 60 Hz. Open Advanced display and check Choose a refresh rate, per Microsoft. BenQ’s checklist puts this right after the monitor’s menu, and Blur Busters’ TestUFO FAQ says drivers, the OS or the monitor’s EDID defaults sometimes put a display back to 60 Hz on their own, so look again after a driver update.
  2. The high rate only exists at another resolution. That’s what Microsoft’s asterisk means. BenQ recommends running the native resolution.
  3. The monitor’s menu isn’t on its top rate. RTINGS and BenQ both say to check the on-screen menu; RTINGS adds any overclock or dual-mode setting.
  4. The cable or port can’t carry the mode. RTINGS’ AOC example shows a 180 Hz monitor held to 144 Hz over HDMI by bandwidth. BenQ says some monitors with both HDMI and DisplayPort run a lower refresh rate over HDMI and that you then need DisplayPort, and that a cheap, low-quality cable can cause flickering and refresh-rate drops. Check the mode in the bandwidth calculator, which also lists the certified cable each link rate needs.
  5. The graphics can’t drive the rate, or the cable is in the wrong port. BenQ says integrated graphics or older discrete cards might not support a monitor’s refresh rate, and to check the card’s specifications and update the driver. On a desktop with a graphics card, the motherboard’s own video ports run from the processor’s graphics; this section of my detection guide shows how to tell which ports you’re using.
  6. A TV input isn’t set up for 4K 120 Hz. These two are regional vendor pages for specific software, so your TV’s menus may differ. LG’s UK HDMI Ultra HD deep color help page (dated 27/05/2025) says that with HDMI Deep Color off an input supports 4K at 60 Hz in 4:2:0, that 4K at 120 Hz needs the setting on 4K (or On) on a 120 Hz model, and that the 4K 120 Hz formats are available only on the HDMI inputs labelled 4K@120 Hz; the setting is per port, and for 2022 webOS 6.0 models the page gives General, Devices, HDMI Settings, which it says changed from earlier models. Samsung’s Singapore Game Mode page (last updated April 4, 2023, and noting that menus vary by model and software version) says to plug a PC into the 4K @ 120 Hz port marked with a game-controller icon, that Game Mode doesn’t turn on by itself for a PC, and that Input Signal Plus, set per HDMI port under All Settings > Connection > External Device Manager, lets the connected device use HDMI 2.1 features. The OLED TV as a PC monitor page covers the rest of a TV setup.
  7. The game is set lower. BenQ says a game with its own graphics settings may use a lower refresh rate unless you pick the monitor’s rate in its menu. A game can also cap its own frame rate at 60; the V-Sync page covers that case.

If the higher rate shows up but the screen flickers or goes black at it, that’s a different problem with its own steps in the monitor flickering guide.

For which port and cable carry each resolution and refresh rate, see HDMI vs DisplayPort for a gaming monitor.

What an online “Hz test” measures

I’ll use TestUFO’s refresh-rate page, from Blur Busters, as the example, because its maker documents what it does. The page says it is designed to measure your display’s refresh rate accurately, that you should wait at least 30 seconds and close other apps and browser tabs first, and that the reading gets more accurate the longer it runs.

It measures through your web browser, and that’s its limit. Blur Busters’ own stuck-at-60Hz FAQ says many browsers don’t run at the display’s real refresh rate and often sit at 60 fps on a faster screen, and that some can’t detect the right rate at all and report 60 Hz on a 120 or 144 Hz display. It says several monitors running at different refresh rates often throw the reading off, and tells you to confirm the rate in Windows before the later steps. TestUFO’s browser page lists the supported browsers and says Safari needs its Prefer Page Rendering Updates Near 60fps setting turned off.

Checking for dropped frames is a separate test. TestUFO’s Frame Skipping Checker, built for display overclocking, needs a camera photo of the screen, and the page says screenshots won’t work. So the refresh-rate reading isn’t Blur Busters’ check for dropped refreshes; the camera test is. I read the rate from Windows and the monitor’s menu first and treat a browser test as a second opinion.

Frequently asked questions

Is 144Hz better than 60Hz?
On the arithmetic, each refresh lasts 6.94 ms at 144 Hz against 16.67 ms at 60 Hz. Blur Busters’ rule for sample-and-hold screens ties eye-tracking blur to how long each frame stays up, so at 144 fps that blur is about 42 percent of what it is at 60 fps, before slow pixel response adds its own. You only get it if the game runs near 144 fps and your cable and port carry 144 Hz. How much you’ll notice depends on you, the panel and the game, and the sources differ on aiming: RTINGS calls high refresh rate a competitive advantage, while NVIDIA’s study of eight esports players found relatively minor effects from refresh rate alone.
Is 240Hz worth it over 144Hz?
Each refresh drops from 6.94 ms to 4.17 ms, a 1.67x step, against 2.4x for 60 to 144 Hz. Blur Busters argues bigger ratios are easier to see and that fast OLEDs show refresh-rate gains more fully than LCDs. NVIDIA researchers who separated latency from refresh rate found refresh rate on its own had relatively minor effects on eight skilled esports players’ task times. By Blur Busters’ persistence rule the gain depends on your games actually running near 240 fps, which the FPS calculator can check for tested setups.
What is Hz on a monitor?
Hz (hertz) is the refresh rate: how many times per second the screen updates its image. Microsoft’s example is a 60 Hz display updating the screen 60 times a second, and RTINGS adds that each refresh redraws the screen from top to bottom.
Is Hz the same as FPS?
No. Hz belongs to the monitor. FPS is how many frames per second the PC or console sends. RTINGS says you ideally want the two to match, and that a mismatch can show up as stutter or screen tearing. Variable refresh rate makes the monitor follow the frame rate instead.
How do I change the Hz on my monitor?
In Windows 11, Microsoft’s path is Start > Settings > System > Display > Advanced display, then pick a rate next to Choose a refresh rate. NVIDIA puts resolution and refresh rate controls in the NVIDIA app’s System tab, Displays section. AMD’s display article sends you to the same Windows setting. RTINGS also says to set the rate in the monitor’s own menu, including any overclock or dual-mode setting.
How do I check what Hz my monitor is running at?
Open Start > Settings > System > Display > Advanced display. Microsoft says the Display information panel there shows the current resolution and refresh rate for the selected display and whether it supports variable refresh rate. The monitor’s own menu is the other place to look; on my AORUS FO48U the Gaming menu shows the refresh rate it is running.
Why is my 144Hz monitor stuck at 60Hz?
The documented causes are: Windows still set to 60 Hz; the high rate available only at another resolution (Microsoft marks those with an asterisk); the monitor’s own menu not set to its top rate; a cable or port without the bandwidth, which RTINGS shows with a 180 Hz monitor limited to 144 Hz over HDMI; graphics that can’t drive the rate, per BenQ; a TV HDMI input not set up for 4K 120 Hz, per LG and Samsung; and a game set to a lower refresh rate in its own menu.
Are online monitor Hz tests accurate?
TestUFO’s refresh-rate page says it is designed to measure your display’s refresh rate accurately if you let it run at least 30 seconds with other apps and tabs closed. It measures through the web browser, though, and Blur Busters’ own FAQ says browsers often stay at 60 fps on a faster display and can report 60 Hz when the display runs at 120 or 144 Hz. Check Windows and the monitor’s menu first and treat the browser test as a second opinion.
Is 120Hz easier on the eyes than 60Hz?
It depends on the person, and I haven’t read a medical study on it, so these are two sources’ claims. Microsoft’s refresh-rate page says a higher refresh rate can reduce eye strain and fatigue. Blur Busters says some people get motion sick from blur when scrolling and need high refresh rates, while for others a low refresh rate is the accessibility setting, and that people need a choice of both.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 22 cited sources, listed below, each checked against the original page on 2026-11-17. Written 2026-11-17 (US Central) from the pages listed below, each opened that day. The time-per-refresh table and the persistence percentages are arithmetic (1000 divided by the refresh rate, and ratios of those figures), labelled as such on the page. Every statement about blur, perception, latency and aiming belongs to the named source. I did not measure motion clarity, input lag, response time or frame rates for this page and did not open the Windows Settings app, the NVIDIA app or AMD Software. First-hand reads on the bench machine, all read-only, on 2026-11-17: Get-ItemProperty on HKLM:\SOFTWARE\Microsoft\Windows NT\CurrentVersion returned ProductName ‘Windows 10 Home’ (the registry string; the build is Windows 11), DisplayVersion 25H2, CurrentBuild 26200, UBR 9974. nvidia-smi –query-gpu=name,driver_version –format=csv returned ‘NVIDIA GeForce RTX 5080, 621.24’. Get-CimInstance Win32_VideoController returned, for the RTX 5080, CurrentHorizontalResolution 3840, CurrentVerticalResolution 2160, CurrentRefreshRate 119, MaxRefreshRate 120, MinRefreshRate 48, DriverVersion 32.0.16.2124; Microsoft documents these fields as uint32 values in hertz. Get-CimInstance -Namespace root\wmi -ClassName WmiMonitorID returned one active monitor named AORUS FO48U. A PowerShell script calling the Windows QueryDisplayConfig API with QDC_ONLY_ACTIVE_PATHS returned one active path whose target refresh rate is 119999/1000 (119.999 Hz) at 3840 x 2160. reg query HKLM\SOFTWARE\NVIDIA Corporation\Global\NVApp returned NVIDIA app version 11.0.9.585, and that app’s English string file (C:\Program Files\NVIDIA Corporation\NVIDIA App\www\assets\i18n\en_US.json) labels its system display page ‘Displays’ with fields ‘Resolution’ and ‘Refresh Rate’; that confirms NVIDIA’s wording, not where the controls sit. There is no Radeon graphics card on this bench (Win32_VideoController also lists the processor’s integrated AMD Radeon Graphics, which reported no current mode), so the AMD statements are AMD’s documentation. The FO48U’s 120 Hz OSD reading is from the screenshots in my existing review of it.
Sources
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

I am Lowell K. Wood IV. I research, write and maintain everything on TechFuelHQ from St. Louis County, Missouri.