Quick answer

A fixed black spot is a dead or stuck pixel, a cluster of them, trapped dust, or OLED wear. Test it free first: full-screen white, red, green and blue, then drag a window across the spot to prove it stays put. Clean the outer surface with a dry cloth before you photograph the result for the vendor.

Contents

At a glance

Class
PC Hardware

Provenance

  • Nov 16, 2026Published

TL;DR · Black spot on a monitor

  • Test before you touch. Solid white, red, green and blue full screen; the spot that survives all four is a panel defect, not content.
  • A single sharp dot and a soft blotch are different faults with different outcomes. Photograph both before you call support.
  • Clean the outside with a dry microfiber cloth and no pressure. Never open the panel to chase a particle.
  • Vendors publish their own limits. LG asks you to contact the seller at six or more dark spots across the three colour tests; check your own model's policy.

A black spot that stays in the same place through every window, webpage and game is a panel problem, not a software one. The useful question is not “how do I remove it” but “which of four things is it”, because only one of them is a warranty conversation and only one of them is your own doing.

The four are a dead or stuck pixel, a cluster of damaged pixels, a trapped particle or surface mark, and OLED wear. Each leaves different evidence, and the tests that separate them cost nothing and take ten minutes. Run those first, in the order below, and keep a photograph of each result.

Four faults, one black dot

What you seeMost likely faultWhat settles it
One sharp pixel, dark on white, no larger than a pixelDead subpixelColour fields show it on every background
One bright or coloured dot on a black fieldStuck subpixelBlack full screen test
Soft-edged speck, unchanged by colour, faintly visible with power offTrapped particle or surface markClean the surface, then recheck
Jagged cluster of dark or discoloured pixelsPressure or impact damageShape and history; usually visible in a built-in test
Ghost of a taskbar, logo or window frameImage retention or burn-inWhether it fades when other content runs

A single dead subpixel is a point defect. A cluster is a physical injury, and it usually has a story: a thumb on the panel while mounting a monitor arm, a keyboard dropped against the screen, a laptop lid closed on a pen. If you cannot find that story, look again at the light: a cluster often has a slightly different sheen at an angle, because the cell structure around it has been deformed.

The free tests, in this order

  1. White first. Fill the screen with solid white. A dead pixel is at its most obvious here, and so is a dust speck.
  2. Red, green and blue. LG’s monitor troubleshooting page uses these three backgrounds because a subpixel can fail on one channel and not the others, which is why a spot can look black on white and coloured on red. Look for the spot on each field and note whether it disappears.
  3. Black. LG’s page also asks you to display black and look for bright spots; a stuck pixel is brightest against black.
  4. The window drag. Open a white document and drag it slowly across the spot. If the spot moves with the window, it is content or a rendering artifact, not the panel.
  5. The input switch. Change to an input with nothing connected, or turn the monitor off and shine a light across the panel at an angle. A mark that is still visible with no signal is on the surface or inside the panel stack.
  6. The built-in test. Use the monitor’s own diagnostics if it has them. Dell’s support article explains that its built-in self-test “helps determine if the screen abnormality is an inherent problem with the Dell monitor”, and directs you to the model’s user guide under Troubleshooting, then Built-in diagnostics.

Write down what you saw for each step. A support agent will ask for the model number, the test used and a photo, and the order of your answers matters more than their confidence.

Prove the spot is fixed to the panel

The window drag is the test most people skip, and it is the one that saves a wasted warranty claim. If the black spot moves when you scroll, the panel is fine and something in the rendering path produced it. Capture it two ways to find out which: take a screenshot and a photograph of the same moment. Corruption that appears in the screenshot came from the rendering path; a spot in the photo that is missing from the screenshot lives in the display or the connection.

Refresh rate belongs here, as a controlled test rather than a fix. The path in Windows 11 is Settings > System > Display > Advanced display, where the refresh rate selector sits, as Microsoft documents on its refresh rate page. Change only that, leave the cable and the resolution alone, and look again. A spot that vanishes at a lower refresh rate is a mode-dependent fault, which points at signal integrity or panel driving rather than a dead cell. A spot that ignores the mode change is a physical defect.

For a monitor that shows nothing at all, rather than a spot, the no-signal guide is the right starting point instead.

Clean the surface before you blame the panel

Turn the monitor off, so a lit white field does not hide a smudge, and look across the glass at a low angle. Most “black spots” that arrive by email are fingerprints, dried cleaning spray, or a fleck of something on the coating.

My approach is a dry microfiber cloth and nothing else to start. Wipe once, gently, and look again with the screen on. If the mark is grease, use only what the monitor’s own manual approves, applied to the cloth rather than the panel, and never spray onto the screen. Two things I do not do: press hard on a spot to see if it moves, and use a paper towel. The first can convert a cosmetic mark into a permanent pressure cluster, and the second can leave fine scratches that look worse than the original defect under a bright field.

One vendor note is worth quoting because it surprises people. LG’s page, describing particles trapped during manufacturing, states that a maximum of one particle per 0.4 mm or less is normal, and suggests that a trapped particle can be removed “by gently tapping the LCD screen”. I would not tap a panel. The tolerance claim is LG’s published position and useful in a warranty conversation; the tapping advice is not something I would risk on a display I had to pay for.

OLED retention is not the same as burn-in

On an OLED monitor, a dark or discoloured patch needs a different test, because the panel ages unevenly rather than failing at one cell. LG’s burn-in page draws the line clearly: image retention “refers to any image that sticks on a screen, even when the content changes”, and “usually appears as a faint ghost, and with most TVs this fades after a moment or two”. Burn-in, in the same document, is “a form of image retention that lasts much longer, and it’s usually visible even when playing other content”.

The practical test is time and shape. Run fifteen minutes of varied full-screen video, then look again. A ghost that fades was retention. A ghost that stays, in the shape of a static element you actually left on screen, is wear. A round black spot is usually neither, which is why I test the colour fields first.

LG’s page also describes the panel-care routine that ships with its OLED sets: a Pixel Refresher that runs automatically after every four hours of cumulative use, plus a longer calibration cycle that starts when you turn the set off after roughly 2,000 hours. Monitor implementations differ, and yours may call it pixel shift, screen move or panel refresh. Follow the manual for your model rather than a forum recipe; running a manual refresh repeatedly is not a repair. Our OLED burn-in census collects what owners actually report by panel and hours, and it is a better guide to the odds than any single case.

What a dead-pixel warranty claim needs

Vendors do not share one threshold, and any article that quotes a universal number is making it up. Some publish a count per million pixels, some exclude certain zones, some treat bright dots differently from dark ones, and most apply different rules to consumer and commercial lines. Read the policy for your exact model before you argue.

LG’s published guidance is concrete enough to quote. Its monitor page instructs readers to contact the seller if “there are 6 or more dark spots including all red/green/blue colors”, and separately, after displaying a black background, to contact the seller if bright spots appear. That is one vendor’s rule for its own products, not a standard.

Dell’s route runs through its diagnostics rather than a pixel count. Its article says that if the abnormality appears in the built-in self-test, the next step is to contact Dell technical support for repair options, and if it does not appear, to continue with display and video troubleshooting. That is why the built-in test in step 6 matters: it converts your observation into the vendor’s own evidence.

Whatever the brand, the file you send should contain the model number, the colour field where the spot appears, a close photograph with a ruler or a coin for scale if the spot is large, the built-in test result, and the purchase date. The Diagnostic Workbench is a reasonable place to keep those observations together before you open a ticket.

When to stop

Stop cleaning, testing and adjusting when any of these is true:

  • The panel is physically damaged. A crack, a spider mark, or a dark blotch that grows after an impact is not a pixel defect. Photograph it and contact the vendor; do not press it to see whether it spreads.
  • The spot appears in the manufacturer’s built-in test. That is the vendor’s own evidence, and further home testing adds nothing.
  • The spots are multiplying. A growing cluster can indicate a failing panel driver rather than isolated cells, and it changes a repair into a replacement decision.
  • You are considering opening the enclosure. At that point the correct move is a service quote, not a toolkit.

Then get the quote before deciding. A single dark subpixel in the corner of a large panel is something plenty of people learn to ignore; a cluster in the centre of the screen is not. That judgement belongs to you and your warranty terms, not to a rule of thumb.

Frequently asked questions

Is a black spot on my monitor a dead pixel?
Sometimes, but not always. A single dark pixel that stays dark on a white background is consistent with a dead subpixel. A round soft-edged blotch, a cluster, or a mark that is visible with the screen off points at dust, a smudge or pressure damage instead. Run the full-screen colour test before you use the word dead pixel in a warranty message.
How do I test a monitor for a dead pixel for free?
Fill the screen with solid white, then red, then green, then blue, and look for spots that do not change with the background. LG’s own monitor troubleshooting page uses those exact backgrounds and also asks you to display black to look for bright dots. A browser in full-screen mode does the job, or use the built-in pattern in the monitor’s service menu if it has one.
Can a black spot be dust inside the monitor?
Yes, and manufacturers know it happens. LG’s monitor page describes trapped particles as a normal manufacturing tolerance, stating that a maximum of one particle per 0.4 mm or less is normal. A particle usually shows as a small dark speck with soft edges that does not change colour with the background. It is not something you can clean from the outside.
Will rubbing the screen remove a black spot?
Cleaning removes surface marks, not internal faults. Use a dry microfiber cloth first, with the monitor off, and do not press hard on the panel. Pressure is one of the ways a small defect becomes a cluster, and it can leave permanent marks of its own. If the spot survives a careful clean and shows up on every colour field, stop touching the screen.
Is a black spot covered by warranty?
It depends on the vendor and the model, and there is no single number that applies across brands. LG’s published guidance, for example, asks you to contact the seller once you find six or more dark spots across the red, green and blue tests, or any bright spot on a black background. Other manufacturers publish their own limits for their own models, so read the policy for your exact panel.
How can I tell burn-in from image retention?
Time and shape. LG describes image retention as an image that sticks even when the content changes, usually a faint ghost that fades after a moment. Burn-in is a form of image retention that lasts much longer and stays visible while other content plays. Retention is a ghost of a shape such as a taskbar; a black spot is usually a point defect, not burn-in.
Does changing the refresh rate tell me anything?
It can. Some panel and cabling faults appear at one mode and not another, so changing the refresh rate under Settings, System, Display, Advanced display is a controlled test as long as you change nothing else at the same time. A spot that disappears at a different refresh rate is a mode-dependent fault, which is different information from a spot that stays fixed.
Should I open the monitor to clean behind the panel?
No. The panel layers are not a user-serviceable assembly, the risk of cracking or distorting the display is high, and opening the enclosure usually ends any warranty coverage. A trapped particle is either within the manufacturer’s tolerance or it is a warranty conversation, not a home repair.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 4 cited sources, listed below, each checked against the original page on the date above. The test procedures and defect counts here come from vendor documentation opened on 2026-11-16. LG’s monitor troubleshooting page supplies the red, green and blue background test, the black background test for bright dots, the six-dark-spot threshold and the trapped-particle tolerance. Dell’s support article supplies the built-in self-test and self-test feature check, including the statement that a self-test identifies whether an abnormality is inherent to the monitor. LG’s burn-in page supplies the distinction between temporary image retention and burn-in. The refresh-rate path is Microsoft’s own support article. No universal dead-pixel threshold is published across brands, and this page does not invent one; it reports LG’s published guidance and tells the reader to check the policy for their exact model.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

Written by Lowell K. Wood IV, who builds and runs TechFuelHQ from St. Louis, Missouri.