Quick answer

Check the tach first. The board reports pump RPM on the header you plugged into, so a running pump shows a number inside its rated range and a dead one shows zero. Confirm the header mode matches the connector, then watch how fast the CPU heats. A warm tube proves nothing; the tach and the temperature curve do.

Contents

At a glance

Class
PC Hardware

Provenance

  • Nov 16, 2026Published

A failed AIO pump is the quietest hardware failure in a PC. The fans keep spinning, the lighting stays on, nothing beeps, and the machine boots normally. The only thing that changes is that the processor starts running hot, and by the time most people notice, they have already blamed the paste, the case, or the weather.

The good news is that the pump is not a mystery component. It reports its own speed, and that number is either inside the manufacturer’s range or it is not. Everything else on this page is about making sure you are reading the right number.

The pump tach is the whole diagnosis

Every pump on a modern AIO has a tachometer output on its control connector. That is the third pin on a standard fan-type header, and it is what the motherboard reads to show you an RPM figure. If the pump is turning, the number is non-zero. If the number is zero or absent on the correct header, the pump is not turning or not reporting.

Know what the range should be before you judge the reading:

CoolerPump speed specificationConnector
ARCTIC Liquid Freezer III 360800–2800 rpm, PWM controlled, 12 V DC, 0.35 A4-pin PWM
NZXT Kraken Plus (2026)1,200–3,200 rpm ±300, Asetek Gen 94-pin PWM
NZXT Kraken Core (2025)3,100 rpm ±310 (fixed)3-pin DC fan header

Those figures come straight from the manufacturers: Arctic’s Liquid Freezer III 360 specification sheet, NZXT’s Kraken Plus pump article, and NZXT’s Kraken Core (2025) spec sheet. Read yours before you test, because “500 rpm” means something different on a 3,100 rpm fixed pump than on an 800 rpm floor.

A pump reading in range does not prove the loop is healthy, and a pump reading zero does not always mean the pump is dead. That is why the next two sections exist.

Read the header before you touch the tubes

People squeeze the tubes first. It feels like evidence. It is not.

The supply tube carries hot coolant away from the block, and the return tube warms partly by conduction along the fitting and the rubber even when the water inside is barely moving. A warm tube tells you the block is hot. It does not tell you the impeller is turning.

Read the header instead. On an ASUS board the fan page lives in Advanced Mode (F7) under Monitor, then Q-Fan Configuration, per ASUS’s BIOS user manual. That page lists every header and the speed it currently reports, which is exactly the reading you need.

Which header should the pump be on? If the board has a dedicated pump header, that is the one. ASUS’s manual for the ROG STRIX B650-A Gaming WiFi says to connect a water-cooling kit’s pump connector to the AIO_PUMP header, and its header table shows that AIO_PUMP defaults to full speed while CPU_FAN and CPU_OPT are Q-Fan controlled. NZXT’s guidance for the Kraken Plus points the same direction: use CPU_FAN or AIO_PUMP, and not a CAM-powered controller.

If the pump is on a header that is switched off in the fan configuration page, you will see no reading at all and the pump may not be receiving what it needs. That is a settings failure masquerading as a hardware failure, and it costs nothing to rule out.

Match the header mode to the connector

This is the step that catches the most false alarms, and it is also the step most guides skip.

Fan and pump headers can run in PWM mode or DC (voltage) mode. ASUS’s BIOS manual lists exactly that choice: PWM Mode for a 4-pin fan, DC Mode for a 3-pin fan. Pick the wrong one and the header either cannot modulate the device or cannot read it properly.

That matters because AIO pumps are not uniform. The Arctic Liquid Freezer III and the NZXT Kraken Plus use 4-pin PWM connectors. The NZXT Kraken Core (2025) uses a 3-pin DC fan header. A 3-pin pump on a header configured for PWM has no control line to talk to, so check the mode against the connector before you decide anything is broken.

While you are in that page, look at the low-speed warning setting. The same ASUS manual shows CPU Fan Speed Lower Limit defaulting to 200 RPM, which exists so the board can warn you that a fan or pump has stopped. If your pump can legitimately idle below that floor, the warning will fire on a healthy cooler. If your pump should never drop that low, the warning is a useful alarm you should leave on.

Is it the pump, the mount, or the firmware?

Three different faults produce the same headline symptom: a hot CPU. Separate them with the table below.

What you observeMost likely causeFirst check
Pump RPM zero, CPU hot within seconds of loadPump not powered or failedPump power lead and header assignment
Pump RPM in range, CPU still hotMounting, contact, or airflowCold plate contact and radiator airflow
Pump RPM correct but drops to zero under loadHeader curve or power deliveryHeader mode, profile, and pump lead seating
Pump RPM normal, temps changed after a BIOS flashFirmware reset header settingsMonitor > Q-Fan Configuration
Gurgling or intermittent RPM after moving the caseAir trapped at the impellerCooler manual’s orientation guidance

The first row is the one that ends in a warranty claim. The second row is the one that ends in a repaste, and it is far more common than people expect. If the pump is turning and the radiator is getting hot, the loop is moving heat; the problem is that heat is not getting into the loop efficiently, or not leaving the radiator.

The fourth row is worth dwelling on. A BIOS update or a CMOS clear can return fan and pump headers to defaults. A header you had set to full speed can come back on a quiet profile, and the pump slows without any hardware change. If your temperatures changed on the same day you flashed firmware, check the fan configuration page before you order parts.

Ordered checks that survive a reboot

Work top to bottom. The first four cost nothing and take minutes.

  1. Boot into the BIOS and open the fan page. Advanced Mode (F7), then Monitor, then Q-Fan Configuration on ASUS boards. Write down the pump header’s RPM and mode.
  2. Confirm the header assignment. Pump on AIO_PUMP if the board has one, otherwise CPU_FAN. Check that the header is not disabled.
  3. Match the mode to the connector. PWM for 4-pin pumps, DC for 3-pin pumps.
  4. Set the pump header to full speed and re-read. On the B650-A the AIO_PUMP header already defaults to full speed, so a pump that still reads zero after this has a power or hardware problem.
  5. Check the pump’s own power lead. Some coolers take power from a separate connector or SATA lead in addition to the tach header. Seat both ends.
  6. Watch the temperature response. If the pump is genuinely dead, the CPU climbs toward its limit quickly under light load. AMD lists 95 °C as the maximum operating temperature for the Ryzen 7 9800X3D and 89 °C for the Ryzen 7 7800X3D; a chip pinned there in a browser is not a fan-curve problem.
  7. Confirm the radiator fans separately. They can run while the pump is still. On the Arctic unit the split cable lets you control pump, VRM fan, and radiator fans independently, which makes this easy to check and easy to misread.
  8. Save your readings. A written record of header, mode, RPM, and temperature survives a reboot. Your memory of a number you saw once does not.

Two things survive a reboot and one does not. A change you make in the BIOS fan page persists. A record you saved to a file persists. A Windows-only fan utility curve may not survive a clean boot or a driver update, which is why I prefer to settle the pump question in firmware before involving software.

If you want the temperature side in more depth, the CPU temperature check guide covers the tools and the safe CPU temperature guide covers the ceilings by model. The thermal throttling guide explains how to confirm the chip is actually being slowed rather than merely warm. If the machine also stops producing a picture, that is a separate display fault; the CPU overheating guide covers the cooling side from the top.

When to stop

Stop troubleshooting and use the warranty when the evidence is unambiguous.

  • Zero pump RPM with the lead seated and the header configured correctly. That is a failed pump, not a settings problem.
  • Pump RPM outside its rated range and a CPU that still overheats. The impeller may be turning without moving coolant. Either way, the unit is not doing its job.
  • Repeated air-lock symptoms after you have followed the cooler manual’s orientation and tilt guidance. Do not keep power-cycling a loop that will not prime.
  • Any leak, smell, or audible grinding from the pump housing. Stop using the machine. Do not open the pump.
  • A pump that works and a CPU that still overheats. That is a mounting or airflow problem, and replacing the cooler without fixing contact will reproduce the symptom. Read the CPU overheating guide before you buy anything.

If you are still uncertain after the checks above, the diagnostic workbench lets you log each step and the reading beside it, so the next person to look at the machine starts from evidence instead of a description.

Frequently asked questions

How do I know if my AIO pump is running?
Look at the pump header’s RPM reading in UEFI or in a monitoring tool that lists motherboard fan headers. A working pump reports a speed inside its rated range: Arctic lists 800 to 2800 RPM for the Liquid Freezer III, and NZXT lists 1,200 to 3,200 RPM for the Kraken Plus. A zero or missing reading on the correct header means the pump is not spinning or is not reporting.
Can an AIO pump fail without making noise?
Yes. A seized impeller or a pump whose power lead is not seated produces no noise at all, which is why the failure is easy to mistake for a fan-curve problem. The symptom is thermal, not acoustic: the CPU climbs toward its limit under a load it used to handle quietly, while the radiator fans keep spinning and sound normal.
Why does my AIO pump show 0 RPM in BIOS?
Three common causes: the pump is plugged into a header that is switched off or set to a mode that does not report, the pump’s own power connector is not seated, or the pump has failed. Confirm the header assignment against the board manual, set the header to full speed for a test, and check the pump’s power lead before assuming the unit is dead.
Should the AIO pump go to CPU_FAN or AIO_PUMP?
Use the pump header if your board has one. ASUS’s manual for the ROG STRIX B650-A Gaming WiFi says to connect a water-cooling pump to the AIO_PUMP header, and that header defaults to full speed rather than Q-Fan control. NZXT tells Kraken Plus owners to use either CPU_FAN or AIO_PUMP and not a CAM-powered controller.
What temperature should a CPU hit if the pump is dead?
It climbs toward the processor’s maximum operating temperature quickly, even at light load, because the block is no longer moving heat into the radiator. AMD specifies 95 °C for the Ryzen 7 9800X3D and 89 °C for the Ryzen 7 7800X3D, so a chip pinned near those numbers at idle or in a browser is a strong signal to stop and check the pump.
Do the radiator fans spinning prove the pump works?
No. Fans and pump are separate loads, sometimes on separate connectors. On the Arctic Liquid Freezer III they can be controlled independently through the split cable, which means the fans can run perfectly while the pump sits still. The pump tach is the only reading that answers the pump question.
Can a BIOS update stop my AIO pump?
A firmware update can reset fan and pump header settings to defaults, and a header previously set to full speed may come back on a quiet voltage curve. If the CPU temperatures changed right after a BIOS flash, open the fan configuration page and confirm the pump header’s mode and profile before you conclude the hardware failed.
When should I stop troubleshooting and replace the AIO?
When the pump reports zero RPM with its power connector seated and the header correctly configured, or when it reports a speed outside its rated range and the CPU still overheats. Do not keep running the machine at its thermal limit while you investigate, and do not open the pump housing. Use the warranty path instead.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 8 cited sources, listed below, each checked against the original page on the date above. Pump speed ranges, connector types, and header behaviour verified November 16, 2026 against Arctic’s Liquid Freezer III 360 specification sheet, NZXT’s official Kraken Plus (2026) and Kraken Core (2025) specification articles, ASUS’s ROG STRIX B650-A Gaming WiFi hardware manual, and ASUS’s BIOS user manual for the STRIX B250F Gaming. Processor limits come from AMD’s own product pages. I did not measure a cooler for this page and quote no temperatures as mine.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

Written by Lowell K. Wood IV, who builds and runs TechFuelHQ from St. Louis, Missouri.