Quick answer

The Jonsbo N5 pairs twelve 3.5-inch lower-chamber bays with an E-ATX upper chamber in a 355 by 403 by 350 mm footprint. It clears 160 mm CPU air coolers and 325 to 350 mm GPUs, provided backplane Molex and SATA power split across separate PSU cables and SAS HBAs get active airflow.

Contents

At a glance

Class
Homelab

Provenance

  • Nov 14, 2026Published

For years, building a 10-to-12-bay home NAS forced an ugly choice. Either you bought a screaming 2U rackmount server chassis that belonged in a concrete basement, or you crammed an expensive Mini-ITX board and an SFX power supply into a shoebox enclosure with nowhere to put both a SAS HBA and a 10GbE card.

Jonsbo’s N5 breaks that compromise. Mini-ITX limits disappear completely. It puts twelve 3.5-inch bays on the ground floor and a full E-ATX workstation chamber upstairs.

Whenever I spec out a twelve-bay ZFS box, I map backplane current and PCIe airflow before picking the motherboard. Read the physical numbers closely first. A twelve-drive chassis carries real footprint, spin-up current, and HBA thermal traps that catch desktop PC builders off guard.

Verified Jonsbo N5 specifications and shelf footprint

Product photos make the N5 look tiny. Pull out a tape measure. It is a wide horizontal cube—wider than a standard mid-tower and deeper than a standard 12-inch bookshelf.

Every dimension and clearance below comes straight from Jonsbo’s N5 specification sheet and the official N5 Installation Manual PDF:

SpecificationOfficial Jonsbo N5 RatingBuild-Planning Impact
Exterior dimensions355 mm (W) × 403 mm (D) × 350 mm (H) (incl. 6 mm feet)Needs at least 450 mm (~18 in) shelf depth once rear power, Ethernet, and video cables bend
Net weight & materials7.5 kg empty (1.0 mm steel + 2.0 mm aluminum + 8 mm North American walnut trim)Add 12 × ~685 g helium HDDs (~8.2 kg) plus PSU/board/cooler and loaded weight tops 20 kg (44+ lb)
Motherboard supportITX, Micro-ATX, ATX, E-ATX, XL-ATXTakes standard ATX/workstation ECC server boards without paying the Mini-ITX tax
Expansion slots8 full-height PCIe slotsRoom for a dual/triple-slot GPU + x8 16i SAS HBA + dual-port 10GbE NIC
Drive bays12 × 3.5" HDD + 2 × 2.5" SSD (or 4 × 2.5" SSD if PSU ≤ 170 mm)Keep ATX PSU length ≤ 170 mm if you want all four 2.5-inch SSD mounts
ATX PSU clearanceStandard ATX PS2 (≤ 170 mm to 240 mm)No SFX PSU surcharge; full modular ATX units fit lower rear chamber
CPU air-cooler limit≤ 160 mm heightClears 155–158 mm dual-tower coolers (Thermalright Peerless Assassin 120 SE 155 mm, Noctua NH-U12A 158 mm); rejects 165 mm NH-D15
GPU length limit≤ 325 mm to 350 mm350 mm bare front; drops to 325 mm with front intake fans and tighter still if mounting a thick front radiator
Fan & AIO mountsRear 3 × 120 mm (pre-installed); Left 3 × 120 mm; Right 3 × 120 mm; Front 2 × 120/140 mm or 240/280 mm AIOLower rear fans pull across the 12-bay cage; upper chamber relies on front/side fans you add

Check two measurements twice before buying a cooler or rack shelf. First, 160 mm CPU height eliminates tall 140 mm-fan towers like the 165 mm Noctua NH-D15 or 168 mm NH-D15 G2, while 155 mm dual-120 towers drop right in. Second, 1.0 mm steel panels sitting around twelve 7,200 RPM enterprise drives will transmit idle hum into hollow furniture, so review our enterprise hard drive noise and chassis resonance guide and place dense neoprene or sorbothane pads under the feet if the box lives near a desk.

Backplane power wiring and 12-drive spin-up math

Rushed wiring burns modular PSU plugs here.

Open page 4 of the Jonsbo N5 Installation Manual and look at the lower chamber floor. Rather than one monolithic 12-port PCB, Jonsbo splits the bays across two separate hot-swap backplanes arranged 8 + 4:

  • 8-bay main backplane: 8 × 7-pin SATA data ports, fed by 2 × 4-pin Molex (peripheral) + 1 × 15-pin SATA power
  • 4-bay side backplane: 4 × 7-pin SATA data ports, fed by 1 × 4-pin Molex (peripheral) + 1 × 15-pin SATA power

Why both Molex and SATA power on the same board? Simple physics. Spinning 3.5-inch hard drives draw motor current on +12V and controller logic on +5V. In Seagate’s Exos X24 SATA Product Manual (Table 7, DC Power Requirements), a single 24TB drive averages around 6.5W at idle and 9.4W under random read/write, yet pulls roughly 2.0A peak on +12V during spin-up.

Multiply 2.0A across twelve bays spinning up together at cold boot, since consumer motherboards and IT-mode HBAs rarely stagger spin-up out of the box:

$$I_{\text{peak, +12V}} = 12 \times 2.0\text{ A} = 24\text{ A} \quad (\approx 288\text{ W transient on } +12\text{V alone})$$

One modular 6-pin peripheral/SATA header on your power supply housing uses a single +12V terminal rated around 7A to 9A continuous on typical 18 AWG wire. Never daisy-chain all twelve drives together. Chaining all three Molex inputs and both SATA power inputs off a single cable plus Y-splitters overloads that single PSU housing pin at cold boot, dropping +12V voltage enough to make drives click, reset, or drop offline during ZFS import.

Wire the N5 backplanes across at least two—and ideally three—independent modular cables plugged into separate 6-pin peripheral/SATA sockets on a quality ATX PSU (check total system draw in our PSU wattage calculator):

  1. Modular Cable A (Molex peripheral): Plug two native Molex connectors into the 8-bay backplane.
  2. Modular Cable B (Molex +/or SATA): Feed the 4-bay backplane’s Molex input and SATA input from a second dedicated modular run.
  3. Modular Cable C (SATA power): Feed the 8-bay backplane’s 15-pin SATA power input (plus any 2.5-inch cache/boot SSDs) from a third cable, and never use cheap molded-plastic Molex-to-SATA adapters.

One bonus for buyers running refurbished enterprise hard drives: Molex carries only +12V and +5V with zero +3.3V wire, and confirm whether your SATA cable supplies +3.3V if using newer PWDIS OEM drives.

SAS HBA cabling and the 200 LFM heatsink trap

Motherboard chipsets rarely expose twelve native SATA ports. Cheap PCIe x1 SATA cards drop drives under load. Twelve bays call for a real Broadcom/LSI HBA flashed to IT (Initiator Target) mode, typically an LSI SAS 9300-16i (4 × SFF-8643 mini-SAS HD) or 9400-16i / 9500-16i (SFF-8654 SlimSAS), paired with three 0.5 m forward-breakout cables (SFF-8643 to 4× SATA) routed neatly through the chamber pass-through without blocking the lower fans.

Do not install an LSI 9300-16i bare in the N5 upper chamber and walk away. Look at Broadcom’s SAS 9300 Host Bus Adapter Product Brief: the dual SAS3008 controller design draws ~27W typical on its tiny passive aluminum heatsink and mandates 200 LFM (linear feet per minute) minimum airflow at up to 55°C ambient.

Rack servers push 200+ LFM easily. Desktop cubes do not. The Jonsbo N5’s three pre-installed rear 120 mm fans sit predominantly behind the lower drive cage, leaving the upper PCIe slots in a calm pocket unless you move air across them deliberately. Without dedicated airflow, a 9300-16i easily crosses 95°C and starts throwing SAS_TASK_ABORT link resets that masquerade as failing drives.

Two easy fixes solve it permanently:

  • Direct heatsink fan (best): Screw or zip-tie a quiet 40 × 20 mm PWM fan (Noctua NF-A4x20 PWM) directly onto the HBA heatsink fins. Even at 2,500 RPM it is inaudible outside the case and drops HBA core temps by 30–40°C.
  • Lower-wattage single-chip HBA + side intake: Choose a newer tri-mode 9400-16i or 9500-16i (single controller IC, roughly half the idle wattage of the dual-chip 9300-16i) and populate the N5’s mesh side 120 mm mounts blowing directly across the PCIe card zone.

Local AI + NAS hybrid clearance (325–350 mm GPU)

The upper E-ATX deck is the real reason homelab builders pick the N5 over a Synology box or 8-bay cube. Because the upper compartment offers 8 expansion slots and 325–350 mm of horizontal length, one machine can combine a 12-drive ZFS pool (size usable parity space in the NAS & ZFS storage calculator and compare best NAS hard drives) with a discrete GPU for Jellyfin AV1 transcoding, Frigate NVR object detection, or local LLM serving.

Plan your PCIe slot map on the motherboard PDF manual before buying the board:

  1. Primary PCIEX16 (x16 from CPU): Discrete GPU (2–3 slots wide; verify card length stays ≤ 325 mm once you mount 25 mm-thick front intake fans).
  2. Secondary PCIEX16_2 (x8 or x4 electrical, PCIe 3.0/4.0): SAS 16i HBA (12 × 275 MB/s peak outer-track HDD sequential throughput totals ~3.3 GB/s, which fits effortlessly inside PCIe 3.0 x8 at ~7.8 GB/s or PCIe 4.0 x4 at ~7.8 GB/s!). Avoid PCIe 3.0 x1 chipset slots at all costs.
  3. Third open slot (PCIe 3.0 x4 or PCIe 4.0 x2+): 10GbE SFP+ or RJ45 NIC—also a server ASIC that appreciates side-panel intake air.

Leave at least one empty slot gap between a triple-slot GPU backplate and the HBA’s 40 mm fan so neither card starves the other, keep your ATX PSU at or under 170 mm so the lower chamber cable bay stays roomy behind both backplanes, and the Jonsbo N5 builds like a proper workstation rather than a knuckle-scraping puzzle box.

Frequently asked questions

How many hard drives fit in the Jonsbo N5?
According to Jonsbo’s official N5 specification and installation manual, the lower storage chamber holds twelve 3.5-inch hard drives across an 8-bay PCB backplane and a 4-bay PCB backplane, plus two 2.5-inch SSD mounts alongside full ATX PSUs up to 240 mm or four 2.5-inch SSD mounts when your ATX power supply stays at or under 170 mm.
What motherboard sizes and CPU coolers fit inside the Jonsbo N5?
Unlike Mini-ITX cube enclosures in the earlier N-series, the Jonsbo N5 upper chamber accepts ITX, Micro-ATX, ATX, E-ATX, and XL-ATX motherboards with eight full-height PCIe expansion slots and up to 160 mm of CPU air-cooler height, plus front mounting for a 240 mm or 280 mm AIO radiator.
How long of a GPU can the Jonsbo N5 hold for local AI or Plex transcoding?
Jonsbo rates the upper chamber for 325 mm to 350 mm graphics cards depending on whether front intake fans or a front AIO radiator occupy the front bracket. With eight expansion slots, you can pair a dual- or triple-slot GPU beside an x8 SAS HBA and a 10GbE NIC on a standard ATX or E-ATX board.
How many power connectors do the Jonsbo N5 backplanes require?
Jonsbo’s N5 manual splits the twelve lower bays into two PCBs: an 8-bay backplane fed by two 4-pin Molex connectors plus one 15-pin SATA power connector, and a 4-bay backplane fed by one 4-pin Molex connector plus one 15-pin SATA power connector. Spread those inputs across at least two or three separate modular peripheral/SATA cables from your PSU rather than chaining twelve enterprise drives onto one ribbon.
Does an LSI 9300-16i or 9500-16i HBA overheat inside the Jonsbo N5?
Without added airflow, yes. Broadcom’s LSI SAS 9300 series product brief specifies a minimum of 200 linear feet per minute (LFM) of chassis airflow across its passive server heatsink. Because the Jonsbo N5 upper chamber lacks high-static-pressure rack-chassis airflow across lower PCIe slots, zip-tie or screw a 40 mm fan directly onto the HBA heatsink or mount side 120 mm intake fans aimed straight across the PCIe zone.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 4 cited sources, listed below, each checked against the original page on the date above. Every chassis dimension, material thickness, drive count, fan mount, PSU length dependence, and backplane connector count on this page comes from Jonsbo’s official N5 product page and N5 Installation Manual PDF, verified 2026-11-14. Enterprise drive spin-up current comes from Seagate’s Exos X24 SATA Product Manual (Rev. C), and HBA thermal airflow requirements come from Broadcom’s SAS 9300 Host Bus Adapter Product Brief.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

Written by Lowell K. Wood IV, who builds and runs TechFuelHQ from St. Louis, Missouri.