Menu
Hardware
Homelab & NAS
Tools & Builders
Prices & Data
Troubleshoot

Flight-Deck First-Boot Protocol · Release QRH-2026.1 · Screen & Printable Toolbox Card

Cold Start QRH: First-Boot PC Flight-Deck Checklist & Shakedown

Flight-deck challenge-and-response checklist for a new PC's first power-on: five red-border memory items, manual-cited POST checks, no-POST flows, and a printable 1-page toolbox card.

Preflight: PSU Wattage → Preflight: UPS Runtime →
Memory: 0/5 · Normal: 0/12
Saved builds from PC Builder & Hardware Projects appear automatically in this menu.

0 · Red-Border Memory Items — Do Before Energizing PSU

Immediate physical stop conditions · Verify by sight and touch

  1. Abort rule: Do not power on if uncertain — unseat the block and inspect before energizing.

  2. Abort rule: Modular PSU-side pinouts are not standardized across brands or even sub-series (EVGA 1000 GT review). Never reuse another supply's modular leads.

  3. Abort rule: Inspect the plug shoulder under a flashlight (ATX 3.1 & 12V-2x6 guide). Re-seat if any seam remains between connector housing and card header.

  4. Abort rule: An extra pre-installed case standoff beneath bare solder points shorts the board to chassis ground.

  5. Citation: ROG STRIX B650-A manual E20268 Sec. 2.3.1, p. 2-20 — plug HDMI/DisplayPort into the graphics card bracket when a discrete GPU is installed.

1 · Normal Preflight, First Power & 30-Day Shakedown (Challenge / Response)

Progress saves automatically in your browser between build evenings

  1. Confirm both 24-pin and primary 8-pin CPU 12V plugs are latched at the board and PSU ends (ASUS E20268 warns never to connect the 4-pin ATX_12V_2 alone).

  2. One module belongs in DIMM_A2; two modules belong in DIMM_A2 + DIMM_B2 on the ROG STRIX B650-A (Compatibility Atlas).

  3. Verify no populated M.2 socket disables a required PCIe or SATA port (NVMe Expansion Checker).

  4. Leaving CPU_FAN unpopulated causes UEFI to halt POST with a CPU Fan Error prompt.

  5. Confirm the two-pin case power switch sits on the power button pins, not RESET# or PLED.

  6. Flip PSU switch to I and pause 5 seconds. Abort immediately on any burnt smell, smoke, or rapid relay clicking.

  7. On AM5 DDR5 first boot, memory training routinely holds DRAM yellow for 60+ seconds (64.0s recorded on our POST Time Census Windows 11 build 26200 fixture). Do not force-power-off during the first 3 minutes.

  8. Verify pump/fan RPM > 0 and CPU package temperature settles rather than climbing toward TjMax (89°C on Ryzen 7 7800X3D per AMD official spec).

  9. Install Windows or Linux at stock JEDEC memory speed first so an untested memory profile cannot corrupt OS installation files.

  10. Log the shipping BIOS build below before flashing firmware (ASUS E20268 Sec. 3.1, p. 3-1 notes menu options vary across BIOS releases).

  11. Enable EXPO/XMP and Resizable BAR in separate reboots after OS + chipset driver install so any fault isolates cleanly.

  12. Confirm 0 hardware errors under WHEA-Logger (WHEA 0x124 guide) and log GPU core-to-hotspot delta (Hotspot Delta Census).

2 · Non-Normal First-Boot Flows (No Power, No POST, No Signal)

Need deeper branching? Escalate into the Diagnostic Workbench

NN-A · Dead System or Instant PSU Click-Off

  1. Switch PSU to O and confirm the wall outlet or UPS switched bank is live.
  2. Verify 24-pin ATX_PWR and 8-pin CPU EPS cables are latched at both ends, and no 6+2 PCIe plug was forced into an EPS header.
  3. Momentarily bridge the two PWRBTN# pins to rule out a dead case switch.
  4. If the PSU clicks off instantly on power press, suspect a short (extra standoff or mismatched modular cable) — follow PC Won’t Turn On.

NN-B · Fans Spin, Stuck on CPU or DRAM LED

  1. Wait a full 3 minutes on first DDR5 boot — initial memory training holds DRAM yellow without screen output.
  2. Power off and seat a single module in the manual’s 1-DIMM slot (DIMM_A2 on ROG STRIX B650-A, p. 1-5) until both side clips lock.
  3. Short the Clear CMOS jumper per manual instructions to clear failed training state.
  4. If CPU red persists with a newer-series CPU on an older board revision, check USB BIOS FlashBack — follow PC Won’t POST.

NN-C · Green BOOT LED with Black Display

  1. Verify HDMI/DisplayPort is in the discrete graphics card, not the motherboard rear I/O.
  2. Power off, re-seat the GPU in PCIEX16_1, and re-check the 12V-2x6 / PCIe power latch under direct light.
  3. Select the monitor’s input manually or test HDMI 2.1 (some DisplayPort monitors miss initial UEFI link negotiation) — follow Monitor No Signal.

3 · First-Flight Logbook & Self-Reported Sign-Off Summary

Stored locally in your browser · Plainly labelled self-reported for support threads or sale listings

Why a flight-deck checklist works better than a build guide at first power-on

Most assembly mistakes happen in the ten minutes between tightening the last side-panel thumbscrew and pressing the case power button: a protective sticker left on the cooler cold plate, a modular SATA or PCIe cable pulled from an older PSU’s box, a 12V-2x6 plug shy of latching by a millimeter, or two DDR5 DIMMs pushed into A1/B1 instead of A2/B2. Aviation Quick Reference Handbooks separate red-bordered memory items (checked before energizing the bus) from challenge-and-response normal items and short non-normal fault flows so you do not troubleshoot from memory while kneeling next to an open chassis.

Where every limit in the worked example comes from

Frequently asked questions

Should I enable EXPO or XMP on the very first boot into BIOS?
No. Verify temperatures, fan/pump RPM, and storage visibility in UEFI first, then install Windows or Linux at stock JEDEC memory speed. Enabling EXPO or XMP after the OS and chipset drivers are installed prevents an unstable memory profile from corrupting OS installation files and makes any subsequent boot failure trivial to isolate.
How long should I wait on a yellow DRAM light during an AM5 DDR5 first boot?
Give a new DDR5 build at least three full minutes before touching the power button. Firmware memory training holds the DRAM diagnostic LED with no display signal; on our Windows 11 build 26200 POST Time Census fixture, Last BIOS time measured 64.0 seconds even on an established machine.
Why do custom builds show prompts instead of pre-filled DIMM slot names?
Primary two-module DIMM slots and PCIe/M.2 lane-sharing rules vary across motherboard layouts and manual editions. Rather than guessing A2/B2 for an uncovered board, QRH: Cold Start auto-fills manual citations only for boards in our Compatibility Atlas (currently the ASUS ROG STRIX B650-A GAMING WIFI, manual E20268) and prompts you to enter your own manual’s exact values.
Can I print this checklist on a single sheet of paper before starting my build?
Yes. Click ‘Print 1-Page Toolbox Card’ (or press Ctrl+P / Cmd+P) to strip navigation chrome and print a high-contrast black-and-white bench card covering the five red-border memory items, the twelve normal challenge-and-response items, and write-in boxes for shipping BIOS version, idle CPU temperature, and Last BIOS time.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 3 cited sources, listed below, each checked against the original page on the date shown beside it. Worked-example slot names, ATX power rules, rear I/O display guidance, and Q-LED sequences cite the ASUS ROG STRIX B650-A GAMING WIFI user manual (E20268, First Edition, September 2022) by section and printed page. Ryzen 7 7800X3D thermal limits cite AMD’s official processor specifications (Tjmax 89°C). Modular PSU cable notes trace to our EVGA SuperNOVA 1000 GT review, and DDR5 training duration cites our POST Time Census fixture.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.