Quick answer

Power the PC down, switch off the power supply and hold the power button to drain it. Clean the case filters first, then blow out heatsinks and fans in short bursts with the blades held still. Use isopropyl alcohol on a lint-free cloth only for thermal paste, never on the board.

Contents

At a glance

Class
Tutorial

Provenance

  • Nov 16, 2026Published

Dust is not cosmetic. It mats the fins, slows the fans that have to push through it, and raises every temperature in the case at once, which is why a machine that ran quiet in January sounds like a leaf blower by July. Cleaning it is a twenty-minute job with a fixed order and a short list of things you must not do.

The order matters more than the tools. Filters first, because that is where most of the dust is and because you do not want to blow it deeper into the case. Heatsinks and fans second. The area around the power supply third. Anything involving liquid is a separate, much narrower job.

Step 1: Power off, unplug, and drain the rails

Corsair’s guide is specific here: power the PC down and set the power supply switch to the off position before you start. I go one step further out of habit. After the PSU switch is off, I hold the case power button for a few seconds, which discharges the standing voltage on the rails so nothing is live when a fan cable comes loose under my hand.

Then unplug the machine from the wall. Not because the switch is unreliable, but because a cable you have not touched cannot be knocked back on by someone else in the room.

Work where dust can land somewhere other than the carpet you sleep on. A garage, a patio, or a well-ventilated room with the machine on a hard surface is fine. The point is that you will be blowing a season’s worth of particulate into the air, and you would rather it not settle back into the case you just cleaned.

Step 2: Clean filters and mesh before anything inside

Corsair calls the dust filters the easiest step and the place to start, and it is right for a practical reason: every filter you clear is dust that never reaches a heatsink. Slide them out or pry off the magnetic ones, then clean them with a damp cloth or under running water.

The one rule that matters is drying them completely before they go back on the case. A damp filter sitting against a metal front panel is a worse idea than a dusty one.

While the filters are off, look at the intake mesh and the top exhaust mesh if your case has them. They clog the same way and they are the reason a machine can run hot with clean heatsinks. This is also the moment to notice whether the front intake is blocked by a drive cage, a cable bundle, or the desk cabinet the case is pushed into, because no amount of cleaning fixes an intake that has nowhere to draw from.

Step 3: Heatsinks, fans, and the PSU shroud area

Open the side panel and work from the top of the case downward, which is what Corsair recommends and what keeps dislodged dust from settling on parts you already cleaned.

Three techniques carry the whole job:

  1. Hold the fan blades still. Corsair’s guidance is to hold the fan still while hitting it with compressed air, and both failure modes it prevents are real. A fan spun far past its rated speed loads the bearing, and a motor driven by an outside force acts as a generator, pushing a voltage back at the header instead of drawing current from it. Use a finger or a plastic tool, never a screwdriver.
  2. Use short bursts, and hold the can upright. Corsair specifies an upright canister and short bursts. Upright keeps the liquid propellant in the can instead of spotting the PCB, and short bursts keep you from parking a jet of cold propellant on one component.
  3. Keep the nozzle back. You want moving air, not a pressure washer. Blasting a heatsink at contact distance drives dust into the fin stack and can knock a fan connector or a jumper loose. Back the nozzle off until you can see the dust leaving rather than feel the jet landing.

Work the CPU cooler fins, then the GPU cooler and its fans, then the case fans, then the nooks around the drive bays. On the motherboard and the RAM, Corsair’s caution is worth following exactly: short bursts only, and no brush on those parts, because a brush catches on a capacitor or a latch and takes it with it. For the fan blades themselves, Corsair’s fan guide suggests wiping them with a clean microfiber cloth first, then using cotton swabs with a small amount of isopropyl alcohol for the gap between the blades and the inner frame, and finishing with compressed air for the loose dust that is left.

The power supply gets air, not disassembly. Corsair lists the PSU as something you can clean with compressed air. That means blowing through the fan grille and the vents from outside the unit. Do not open a power supply to clean it; the capacitors hold a charge after the unit is unplugged, and there is nothing inside that user cleaning improves.

If the machine sits in a case with a PSU shroud, clean the shroud’s vents and the floor filter under it. That is where the intakes for the power supply and often the bottom case fans live, and it is the area people forget because it is at floor level and out of sight.

Step 4: Isopropyl alcohol belongs on a cloth, not the board

Isopropyl alcohol has exactly one job in a PC: removing thermal paste from a CPU heat spreader and a cooler cold plate. Corsair’s thermal paste instructions say to clean both surfaces with a paper towel lightly moistened with isopropyl alcohol before applying new paste. Damp, not wet. The cloth does the work.

The concentration is where vendor guidance stops agreeing with itself. Corsair specifies isopropyl alcohol without naming a percentage, and cooler and paste makers publish their own wording, which does not always match. So I will not give you a number that no manufacturer in front of me printed. Follow the instructions that came with your cooler or your paste, and if they conflict, follow the cooler’s, because it is the part with a warranty on the surface you are wiping.

What alcohol is not for: the motherboard, the GPU board, connectors, fan hubs, or anything you would describe as “wiping down.” Do not pour it on the board, do not spray it at the board, and do not use it to chase dust into a socket. Alcohol on a cotton swab for a fan’s inner frame, as Corsair’s fan guide describes, is a different and much smaller operation than wetting down a PCB.

What not to do, and why

Most cleaning damage is not subtle. It is a specific mistake that seemed reasonable at the time.

Do notWhy
Put a vacuum nozzle on the boardSuction tools generate static, and a plastic nozzle dragged across components is the wrong combination to introduce into a live-adjacent machine
Use water inside the caseWater is for removable filters, which then have to be fully dry; nothing inside the case is meant to get wet
Spray canned air at an angle so it spitsHolding the can upright and using short bursts is what keeps liquid propellant off the PCB
Let fans freewheel under airBearing load and back-fed voltage at the header, which is why the blades get held
Brush the motherboard and RAMCorsair’s caution is explicit: short bursts of air only on those parts
Repaste because you are already in thereA remount changes mounting pressure and paste spread; without a temperature baseline you cannot tell whether you improved anything
Open the power supplyStored charge, no user-serviceable parts, and nothing to gain

The repaste line is the one I get asked about most. If the cooler is working, a cleaning session should end with the cooler exactly as it was. If temperatures are the reason you opened the case, diagnose that first with the CPU temperature check and the safe temperature ranges, then decide whether the thermal interface is implicated. Cleaning dust out of a cooler and remounting it are two different jobs with two different risk profiles.

How often to clean: read the dust, not the calendar

Corsair’s general rule of thumb is every three to six months. It shortens that to two to three months for a dusty area, a home with pets, or indoor smoking, and considers a twice-yearly clean adequate in a relatively dust-free environment.

I use those numbers as a range and let the machine set the interval. Once a month, look at the front intake filter without opening anything. If it is visibly matted, that machine needs a shorter cycle than the calendar suggests; if it is barely hazy after two months, the six-month end of the range is fine. A machine on a carpeted floor next to a shedding dog and a machine on a hard floor in a closed office are not on the same schedule, and pretending they are is how people either waste an afternoon or cook a GPU.

Season is a reasonable proxy in most homes, because heating season and air conditioning season change how much particulate circulates. It is a worse proxy than the filter in front of you.

What to check after reassembly

Before the side panel goes back on:

  • Every fan header is seated on the header it came off, and no cable is resting where a blade will hit it.
  • The filters are dry and fully seated.
  • Nothing is resting on the top of the power supply shroud or blocking a front intake.

Then power on and check the machine, not the panel:

  1. Every fan spins. Open the board’s hardware monitor screen in UEFI, or watch the fans at first POST. A fan that does not spin after a cleaning is usually a header you missed, and occasionally a cable you strained.
  2. Temperatures return to baseline. Idle first, then the same load you used before cleaning. A number that is worse than it was before you opened the case is a reason to stop and look, not a reason to close the panel.
  3. Nothing new is audible. A tick or a scrape is a cable in a blade or a fan that is not seated flat.

If a fan will not spin at all, work through the fan fault check before replacing it. If temperatures are still high with clean filters and spinning fans, the problem is airflow, mounting, or the cooler itself rather than dust, and the thermal throttling walkthrough and the diagnostic workbench are the next stops. For a GPU that stays hot after a clean, the GPU overheating guide covers what the sensors can and cannot tell you before you consider opening the card.

Frequently asked questions

Can I use a vacuum cleaner inside my PC?
Not with the nozzle against the board. Vacuum tools generate static, and a plastic nozzle dragged across components is the wrong combination to introduce into a working machine. I use dry air to move dust off the board and keep any suction well away from it. Loose dust that has already been blown out of the case can be cleaned up afterwards with whatever vacuum you like.
Do I need to hold the fans while blowing them out?
Yes. Corsair recommends holding the fan still while hitting it with compressed air, and the reason is mechanical as well as electrical: a fan hub spun far past its rated speed loads the bearing, and a motor spun by an outside force generates a voltage at the connector instead of consuming one. Hold the blades with a finger or a plastic tool, and never with anything metal that could slip into the board.
What isopropyl alcohol should I use on a CPU?
Corsair’s thermal paste instructions say to clean the CPU and the cooler cold plate with a paper towel lightly moistened with isopropyl alcohol, without naming a concentration. Cooler and paste makers publish their own wording, and the numbers they settle on do not always match each other. Because the guidance genuinely differs between manufacturers, follow the instructions that ship with your specific cooler or paste rather than a number from a forum.
How often should I clean my PC?
Corsair’s general rule of thumb is every three to six months, with two to three months for a dusty home, pets, or indoor smoking, and a twice-yearly clean as adequate in a dust-free environment. I use the filters as the real gauge: if the front filter is visibly matted at the monthly look, the interval for that machine is shorter than the calendar suggests.
Is it safe to wash dust filters under the tap?
Corsair says filters can be cleaned with a damp cloth or running water, then must be fully dried before they go back on the PC. That guidance is for the removable filter, not for anything inside the case. Dry the filter completely, and do not put a damp filter back into a running machine.
Should I repaste my CPU while I am already cleaning?
Only if you have evidence the thermal interface is the problem. A cleaning session is not a reason to break a working cooler mount, and a remount introduces new variables: mounting pressure, paste spread, and a cooler that may not seat the same way twice. Check temperatures against a baseline first, then decide.
Is an electric blower better than canned air?
An electric blower moves more air for longer and does not spit propellant, which makes it the tool I reach for on a full teardown. It also spins fans harder if you are careless, so the hold-the-blades rule matters more, not less. Canned air stays useful for tight spots and for anyone who cleans once or twice a year.
What should I check after putting the PC back together?
Check that every fan header is seated on the right header, that all fans spin, that no cable is resting in a fan blade, and that idle and load temperatures match what the machine did before you opened it. If a fan does not spin or a temperature is worse than baseline, stop and diagnose rather than closing the panel and hoping.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 3 cited sources, listed below, each checked against the original page on the date above. The cleaning order, the hold-the-fan-blades instruction, the motherboard and RAM cautions, the filter rinsing rule and the seasonal cadence come from Corsair’s own PC and fan cleaning guides, read November 16, 2026. Isopropyl alcohol use for thermal paste removal comes from Corsair’s TM40 quick start guide, which specifies the alcohol but not a concentration, so this page states that vendor guidance differs instead of inventing a percentage. No temperature, airflow or timing numbers are claimed as measurements.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

Written by Lowell K. Wood IV, who builds and runs TechFuelHQ from St. Louis, Missouri.