Quick answer

Install one standoff under every screw hole on your motherboard and none anywhere else. An ATX board’s holes follow the ATX specification’s nine locations; a microATX or Mini-ITX board uses a different set of holes, so count the holes on your own board. Before power-on, confirm each standoff has a hole above it and each hole has a screw.

Contents

At a glance

Class
Tutorial

Provenance

  • Nov 18, 2026Published

Put a standoff under every screw hole in your motherboard and nowhere else. The ATX specification defines nine mounting locations for a full ATX board, and ASUS’s manual for the board in my bench PC says to use nine screws. Smaller boards use a different set, and a Mini-ITX board I checked uses four, so count the holes on yours before you touch the case. Then check that every standoff has a hole above it and every hole has a screw.

What standoffs are for

A standoff is a post that screws into the case’s motherboard tray and lifts the board off the metal. Intel names a motherboard screwed directly to the case without the required standoffs as a common cause of an electrical short. The ATX specification also sets the gap: the chassis must leave 0.250 inch of clearance below the board, and the specification excludes the standoffs at the mounting holes from that rule. ASUS’s installation article says to install the standoffs for the 9 screw holes of its example board, then set the board on them with the rear I/O aligned.

How many, and where

Use the board, not the case, as your guide.

Form factorWhat a source says
ATXThe ATX 2.2 specification lists the locations A, C, F, G, H, J, K, L and M, which is nine. ASUS’s manuals for the B650-A and its install article both say nine screws or holes.
microATXThe same specification table lists B, C, F, H, J, L, M, R and S for microATX, and says R and S were added for it. It also says the ATX holes line up with microATX holes where possible. The table lists nine locations for microATX. I did not open the separate microATX specification, so that table is my only specification source for it.
Mini-ITXASUS’s manual for its ROG STRIX B650E-I Mini-ITX board says four screws.

The letters are the specification’s labels, not what your case prints on the tray. NZXT’s H6 article, for example, labels mounts A and U. A few specification details matter in practice. The specification says hole F must be implemented in ATX 2.2 chassis. Hole B was previously required at the rear edge but is no longer needed for ATX, and if a case builder uses it the specification says a removable standoff should be used so boards that skip it are not affected. So a standoff at B under an ATX board is a case to check.

Case makers say the same thing in their own words. ASUS says different board sizes have holes in different places, so cases offer several standoff positions, and you should install only the standoffs your board needs. Fractal Design’s manuals carry a warning to match the motherboard mounting holes to the standoffs.

If you are not sure which board you own, the motherboard model guide shows how to check.

Screws and thread types as case makers document them

Every case manual I opened lists 6-32 for the board screws:

  • Corsair FRAME 4000 and 3200D: 18 motherboard and HDD screws, 6-32 UNC, 6 mm.
  • NZXT H5 Flow: a 6-32 x 5 mm screw for motherboard installation, and the H6 article gives 6-32 x 5 mm mounting screws.
  • Fractal Design Meshify 2 and North: a mounting screw marked 6-32, plus a standoff tool and a spare standoff in the Meshify 2 kit.

NZXT’s H5 Flow manual lists a separate M3 x 5 mm screw for 2.5-inch drives, so a case can ship both threads in one bag. I found no case maker that documents an M3 board screw and no source that says what happens if you swap the two, so follow your case manual. Your motherboard will not supply the screws: ASUS’s package contents for the B650-A list cables, antennas, M.2 parts and a cable-tie pack, with no case screws.

Pre-installed standoffs and the centre post

Some cases ship with standoffs already fitted. Corsair’s FRAME 4000 and 3200D tips say that if the pre-installed standoffs do not align with your board, remove the unused ones and move them to the open mounting points. NZXT’s H6 ships configured for ATX and ITX, and for microATX you move some standoffs from the lower mounts marked A to the upper mounts marked U.

One case documents a centre post. NZXT’s H6 article says the case includes a raised centre standoff that helps align the board, and tells you to lower the board so all the standoffs meet the screw holes. I could not find a second case maker that describes one, so check your manual instead of assuming yours has it.

What a misplaced standoff can do

ASUS and MSI warn about extra standoffs, and neither names the exact part. ASUS says to remove any standoff that does not match a hole, to avoid extras touching the back of the board and causing damage. MSI says any unnecessary standoff between the board’s circuits and the case is prohibited, and says its MAG B650M MORTAR has “Case standoff keep out zone” signs printed on the back. Intel names the opposite error, a board with no standoffs at all.

The ATX specification explains the geometry. It forbids components within a 0.400 inch square around each required mounting hole on the underside, and allows other underside parts up to 0.098 inch tall, including conductive parts the specification calls intolerant of direct connection to chassis ground. Those are the specification’s underside limits; neither it nor ASUS nor MSI says which part a stray standoff would touch.

Check before you power on

  1. Count the holes on the board and the standoffs under it. They should match.
  2. Lower the board and look. Any standoff with no hole above it comes out, which is what ASUS and Corsair tell you to do.
  3. Put a screw in every hole, and do not overtighten. ASUS’s manual warns that overtightening can damage the board.
  4. If your board prints keep-out signs on the back, make sure no standoff sits under one. MSI describes this on the MAG B650M MORTAR; check whether yours has them.
  5. Look for loose screws or metal in the case. MSI’s manual says to make sure there are none before you turn the computer on, and Intel’s troubleshooting page says to look for anything that could cause an electrical short.

If the PC does not start, the no-POST guide and the no-power checklist give the order to work in. A stray piece of metal is easier to find with the board still accessible, and the PC cleaning guide covers opening the case safely. Once the build works, overclocking is a separate job.

If you need a kit

The cases I read include the board screws. A separate kit only helps if you lost them or need extra standoffs. Match the 6-32 thread your case manual lists.

I may earn a commission if you buy through these affiliate links. As an Amazon Associate I earn from qualifying purchases.

Search AmazonLink checked 2026-11-17 Search NeweggLink checked 2026-11-17

The PC Builder holds the rest of the parts list while you check case and board compatibility.

Frequently asked questions

What size screws are typically used for motherboard standoffs?
The case makers whose manuals I read list 6-32 screws for the board. Corsair’s FRAME 4000 and 3200D guides list motherboard and HDD screws as 6-32 UNC, 6 mm. NZXT’s H5 Flow manual lists a 6-32 x 5 mm screw for motherboard installation, and its H6 article says the same. Fractal Design’s Meshify 2 and North manuals list a 6-32 mounting screw. Your motherboard maker does not supply them: the ASUS ROG STRIX B650-A package contents list no case screws.
Why do motherboards need standoffs?
They hold the board off the metal tray. Intel’s troubleshooting page names a motherboard screwed directly to the case without the required standoffs as a common cause of an electrical short, and the ATX specification requires the chassis to leave 0.250 inch of clearance below the board, apart from the standoffs at the mounting holes.
Where can I buy PC motherboard screws?
Start with the accessory bag that came with your case, then your case maker’s support page. Corsair sells a 12-pack of standoffs for the 4000 series, and its FRAME 4000 and 3200D kits include a spare standoff. If you need a kit, match the thread your case manual gives, which is 6-32 for the cases I checked.
Are motherboard screws included with a case?
For the cases I read, yes. Corsair’s FRAME 4000 and 3200D guides list 18 motherboard and HDD screws, NZXT’s H5 Flow manual lists a 6-32 x 5 mm screw for the board, and Fractal Design’s Meshify 2 and North manuals list 6-32 mounting screws, with a spare standoff and standoff tool in the Meshify 2 kit. Check your own case’s accessory list.
How do I know if I killed my motherboard?
I have no source that ties a symptom to a dead board, so I will not guess. ASUS’s no-boot article works in an order: check the power supply, the CPU, the memory and the graphics card, test with minimal components, clear CMOS, then read the Q-LED. Intel adds that a short from a missing standoff is something to look for inside the case. Our no-POST guide walks that order.
Can a standoff in the wrong place damage a motherboard?
The vendors say it can. ASUS says to remove standoffs that do not match a screw hole, because extras can touch the back of the board and cause damage. MSI’s manual says any unnecessary standoff between the motherboard circuits and the case is prohibited, and says its MAG B650M MORTAR has Case standoff keep out zone signs printed on the back. Neither says exactly which part is hit.
Do I need standoffs if my case has a raised centre post?
Yes. NZXT’s H6 article describes a raised centre standoff that helps align the motherboard. It does not say the board needs no further standoffs, and the same article tells you to line the board up so all the standoffs meet screw holes.

Sources and corrections

Last updated
Methodology
See our methodology for research and review standards. It draws on 14 cited sources, listed below, each checked against the original page on 2026-11-17. Hole locations come from the ATX Specification version 2.2 (an Intel document, read as a PDF copy hosted at xdevs.com). Screw counts for ATX and Mini-ITX come from the ASUS user manuals for the ROG STRIX B650-A GAMING WIFI and ROG STRIX B650E-I GAMING WIFI. Screw and standoff details come from the Corsair FRAME 4000 and 3200D guides, the NZXT H5 Flow manual and H6 support article, and the Fractal Design Meshify 2 and North manuals. Warnings about extra standoffs come from ASUS, MSI and Intel. I did not open the standalone microATX or Mini-ITX form-factor specifications: for microATX I rely on the hole table inside the ATX 2.2 document, and for Mini-ITX on one ASUS manual, so I give no Mini-ITX hole letters. First-hand reads on the bench PC, November 17, 2026: Get-CimInstance Win32_BaseBoard returned ASUSTeK ROG STRIX B650-A GAMING WIFI, and I took the board’s screw count from ASUS’s manual for that model, not from opening the case. I did not install or remove a standoff for this page.
Corrections
Spotted an error? Email a correction with the affected line and what you found. The draft includes this page’s address. Verified changes are recorded here. Contact details.

About the author

I am Lowell K. Wood IV. I research, write and maintain everything on TechFuelHQ from St. Louis County, Missouri.